Fitting a Monoblock

FittingaMonoblock

Damp, Condensation, Rot and Woodworm

Fencing, Decking, Paving and Patios

General Building, Self Build and Renovation

Heating, Central Heating and Boilers

Planning Regs, Project Management and Safety

Plastering, Plasterboard and Rendering

Working With Tradesmen – Ultimate Guide

HomeDIY How To Projects and Tutorial GuidesFitting a Monoblock Mixer Tap How to Replace and Connect a Kitchen or Bathroom Mixer Tap

How to fit a monoblock tap to a kitchen sink, basin or bath. Learn how to connect, fit or replace a mixer tap in your kitchen or bathroom. And get some hints ideas which tools will make this project a little easier.

Dont want to do this job yourself?Let us help you find a tradesman local to you

It has to be said that fitting a monoblock mixer tap is not the easiest operation in the world and can certainly be a bit fiddly. However, this project should go some way to making it a little easier.

If you do not have any isolation valves handy to cut off the water supply while you carry out your work then you will have to ensure that the water is turned off. Additionally, while the water is off its a good idea to fit isolation vales for any work you may need to carry out in the future.

The monoblock is a very clever piece of design technology which allows both the hot and cold feed to enter the base, or block of the tap. The temperature is then mixed by the operation of the tap valve or handles.

In order for both feeds to get through the same opening they are reduced to 10mm or 8mm and special tap connectors are used to screw into the block.

The image above shows the tap at the top with the connection tails at the bottom ready to receive the hot and cold feeds. The 10mm feed pipes screw into the underside of the tap and are then machined out to become 15mm copper tails ready for the connection of 15mm feeds.

This can be seen more easily in the image below.

Mounting plate for mixer tap seen from underneath a sink

The opening for a monoblock mixer is usually 26mm. This will be, or be close to, the size of the hole in your sink, basin or bath.

There should be a large rubber O ring which sits underneath the block and is squashed between the top of the sink and the underside of the block as the monoblock is tightened into place.

A large, flat rubber washer is placed on the underside of the basin and this has holes in it which should line up with the holes in the monoblock.

The larger two of these holes are for the feed pipes to be screwed in and the smaller two are where the threaded connection bars are screwed into.

Underside of mono block tap showing feed pipe holes and holes for threaded connection bar

These threaded bars should be fitted before dropping the tap through the hole in the basin. Only do them up as tight as you can by hand. If you use pliers or grips there is a danger you will damage the thread.

Once the tap is in the hole with the flat washer or mounting plate placed over the threaded bars, the steel washer can be slid into place also.

On some models of mixer tap there is only one threaded bar making the job a great deal easier.

Monoblock tap with single nut fixing

Tighten the Nuts on the Threaded Bar

With the washer in place the nuts can now be tightened onto the threaded bar and this is where the DIY enthusiast struggles.

There is hardly any room under the basin, less under a bath and a kitchen sink is a nightmare! Plumbers on the other hand, carry a box spanner which is a long open tube with the correct size nut shaped hole at the end.

It is slid over the thread and the other end twisted tight by putting a nail or something similar into the hole and turning. Easy!

Once the tap is securly fixed into place you can now go ahead and connect up any pipework.

Speedfit fittings can be used on monoblock feed pipes soclick into the speedfit project to see moreor you can use standard fittings but make sure they are the correct size of course.

Ensure that any compression fittings are tightened up sufficiently and you can then turn back on the water or open any isolation valves.

Once pressurised, check your work for any leaks.

All project content written and produced byMike Edwards, founder of DIY Doctor and industry expert in building technology.

Dont fancy doing this project yourself? We work with the industries best to ensure that we recommend only reliable and trustworthy tradesmen.

Let DIY Doctor help you find a tradesman

Related Projects That May Help You:

Advice on Connecting Taps to Basins and Sinks How to Fit Flexible Tap Connectors

Water Filter Taps How do Water Filter Taps Work to Filter Water and When can They be Used

Fitting an Outside Tap How to Install a Garden Tap Yourself Easily

Changing Taps How to Change a Tap on a Kitchen Sink, Basin or Bath Including the Different Types of Tap and how Each Type Works

Ceramic Disc Taps Ceramic Disc Tap Fitting or Servicing with Washer and Valves Repair or Replacement Tutorial

We love feedback on our DIY tutorials it helps us to make them the best they possibly can be so if you have any comments you would like to share with us, click the button below and let us know.

Grab your copy now for all the DIY help you need right at your finger tips!

Keep up to date with our DIY projects, tips and latest deals

Leave a comment